Choosing a Cordless Drill

Whether you’re just learning the basics of simple care or are carrying on another addition to the home, a good drill is vital. And if it’s a cordless version, it is possible to drill holes and drive screws with the same tool — and not need to worry about finding an outlet close to the work to power the drill. The good news: There are countless of these drills in the marketplace. The good thing: It isn’t always apparent which drills you need to be contemplating.

Power, Handles, Clutch

For cordless drills, power is measured in voltage. Higher voltage means more torque-spinning strength to overcome resistance. Today’s higher-voltage drills have sufficient power to bore large holes in framing timber and flooring. That is muscle. But the trade-off for electricity is weight. Handles Before cordless drill/drivers came, most drills had pistol grips, in which the handle is behind the motor like the handle of a gun. But the majority of the modern cordless versions are equipped with a T-handle: The manage foundation flares to prevent hand slippage and adapt a battery. Because the battery is based under the weight and bulk of this motor, a T-handle supplies better overall balance, especially in thicker drills. Additionally, T-handle drills may often get into tighter spaces as your hand is from the way in the middle of this drill. But for heavy duty drilling and driving large screws, a pistol grip does let you use pressure higher up — almost directly behind the bit — allowing you to put more force on the work.

A flexible clutch is the thing that separates electric drills from cordless drill/drivers. Located just behind the chuck, the clutch disengages the drive shaft of the drill, which makes a clicking sound, when a preset level of immunity is attained. The result is that the motor is turning, but the screwdriver bit is not. Why does a drill need a clutch? It gives you control so you don’t strip a screw or overdrive it once it’s snug. Additionally, it can help protect the motor when a great deal of resistance is fulfilled in driving a screw or tightening a bolt. The number of separate clutch settings varies depending on the drill; better drills have 24 settings. With this many clutch settings, it is possible to really fine-tune the power a drill delivers. Settings with the lowest amounts are for small screws, higher amounts are for bigger screws. Most clutches have a drill setting, which permits the motor to push the bit at full strength.

The cheapest drills run at one rate, but many have two fixed rates: 300 rpm and 800 rpm. A slide switch or trigger lets you select low or high rate. These drills are excellent for many light-duty operations. The low rate is for driving screws, the high speed for drilling holes.

For more refined carpentry and repair jobs, select a drill which has the exact same two-speed switch plus a cause with variable speed control that lets you vary the rate from 0 to the top of every range. And if you do much more gap drilling compared to screwdriving, start looking for more rate — 1,000 rpm or greater — at the top end.

Batteries and Chargers
Nickel-metal-hydride (NiMH) batteries represent the most recent breakthrough in batteries. They are smaller and run more than standard nickel-cadmium (Nicad) batteries. Makita, Bosch, Hitachi and DeWalt offer NiMH batteries, along with other manufacturers will soon create these power cells too. All cordless drills include a battery charger, with recharge times that range from 15 minutes to 3 hours. But faster is not necessarily better. A contractor might depend on quick recharges, but slower recharging is not usually a concern at home, especially if you’ve got two batteries. What is more, there are drawbacks to rapid charging. A fast recharge can harm a battery by creating excessive heat, unless it’s a specially designed unit. These components supply a fee in as few as nine minutes without battery harm.


Check out drills at home centers, imagining their weight and balance. Try vertical and horizontal drilling positions to see how comfortable you feel. Contoured grips and rubber cushioning on some versions make them quite comfortable, even when you’re employing direct palm pressure. Home centers often dismiss hand tools, so be watching out for promotions. If you know the version you need, check out costs over the phone.

Match the Tool to the Job
With all the different versions of drill/drivers available on the current market, it’s easy to buy more tool than you actually need. The solution: Purchase a drill based on how you will use it. It doesn’t make sense to pay $200 for a tool you’ll use only to hang pictures. Nor can it be a good idea to pay $50 for a drill just to have the motor burn out after a couple of days of heavy work. You don’t need to drive yourself crazy trying to think up all of the probable jobs you’ll need for your new tool. Look at the 3 situations that follow below and determine where you match. Or lease a more powerful the best cordless drill for those projects that need you.